Aktuelle Inhalte als RSS-Feed anzeigen


In unserem Blog möchten wir Ihnen wertvolle Beiträge zu Themen in Bereichen wie ADS-B, Mode-S, MLAT, Flight Tracking, Antenntechnik und 1090 MHz geben.
Wenn Sie Interesse an speziellen Beiträgen haben, lassen Sie es uns wissen: support@jetvision.de

Veröffentlicht am von

RTL1090 IMU Software

Gesamten Beitrag lesen: RTL1090 IMU Software

Several of our users when installing RTL1090 software report a problem like "No internet connection" or similar. This was due to some old historic software in some kind of caches and link constrcuts which were not under our control. Jetvision now provides a downloadable archive under https://www.jetvision.de/manuals/rtl1090imu.zip and more information at rtl1090.com.

Gesamten Beitrag lesen
Mehr über: Dongle, rtl1090
Veröffentlicht am von

FLARM Range Improvement

Gesamten Beitrag lesen: FLARM Range Improvement

English Version

German Version

FLARM Range Improvement

A well-known shortcoming of many FLARM systems in airplanes is the low reception range. Many users wish for an improvement here and would like to receive other FLARM equipped aviators at a greater distance.

Why is an improvement in range desired? On the one hand, the area of "situational awareness" cannot be large enough; on the other hand, the low standard range of fast airplanes makes little use, since the reaction time is usually too short. Not least because of this, a larger foresight is desirable for the glider pilots, because then other gliders can be recognized in a good thermals far away.

Technically, the increase in the reception range can only be solved by a higher sensitivity of the receiving system, since the transmission parameters of the FLARM devices are fixed and must not be changed. A simple preamplifier between the antenna and the FLARM device is not applicable here, because FLARM devices also transmit, which would destroy any normal receiver preamplifier, and the transmission signal would not reach the antenna.

Jetvision now has solved this problem and developed two new products: 
FLARM BOOSTER  and FLARM BOOSTER PLUS. An optimized low-noise preamplifier typically increases the range of the FLARM device up to four times, and bypasses the transmission signal unmodified. Switching from receive to transmit is done automatically. Existing antennas can be used with the FLARM BOOSTER, the FLARM BOOSTER PLUS comes with an attached optimized antenna. Both devices can be powered over the antenna cable (5V-15V), which greatly simplifies the installation of the preamplifier or the antenna.


FLARM Reichweite verbessern

Ein bekanntes Manko vieler FLARM Systeme in Flugzeugen ist die geringe Empfangs-Reichweite. Viele Anwender wünschen sich hier eine Verbesserung und möchten andere mit FLARM ausgerüstete Flugzeuge auch aus größerer Entfernung empfangen.

Warum ist eine Verbesserung der Reichweite gewünscht? Zum einen kann der Bereich der „Situational Awareness“ nicht groß genug sein, zum anderen nutzt die geringe Standard-reichweite bei schnellen Flugzeugen wenig, da die Reaktionszeit meist zu kurz ist. Bei den Segelfliegern ist nicht zuletzt auch deshalb eine größere Vorausschau erwünscht, da dann andere Segler in einer guten Thermik auch weit entfernt erkannt werden können.

Technisch gesehen ist die Vergrößerung der Empfangsreichweite nur durch eine höhere Empfindlichkeit des Empfangssystems zu lösen, da die Sendeparameter der FLARM Geräte feststehen und nicht verändert werden dürfen. Ein einfacher Vorverstärker zwischen Antenne und FLARM Gerät ist hier nicht anwendbar, da FLARM Geräte auch senden, was jeden normalen Vorverstärker zerstören würde, und das Sendesignal nicht mehr zur Antenne käme.

Jetvision hat sich dieser Problematik angenommen und zwei neue Produkte entwickelt: FLARM BOOSTER und FLARM BOOSTER PLUS. Ein optimierter und rauscharmer Vorverstärker erhöht die Reichweite des FLARM Gerätes typisch bis zum Vierfachen, und leitet das Sendesignal unverfälscht durch (Bypass). Die Umschaltung von Empfang nach Senden erfolgt dabei automatisch. Mit dem FLARM BOOSTER können vorhandene Antennen benutzt werden, der FLARM BOOSTER PLUS kommt mit einer auf ihn zugeschnittenen, angebauten Antenne. Beide Geräte können über das Antennenkabel mit Strom (5V-15V) versorgt werden, was den Einbauort des Vorverstärkers oder der Antenne erheblich vereinfacht. 

FLARM Reichweite

Gesamten Beitrag lesen
Mehr über: 868, 868 MHz, FLARM
Veröffentlicht am von

Yagi 1090 MHz Antenna

Gesamten Beitrag lesen: Yagi 1090 MHz Antenna

Over the christmas holiday our Radarcape demo station has got a new yagi towards Munich airport EDDM/MUC in order to improve the tracking of ground traffic. The airport is around 30 km east from the location of Jetvision headquarters but a not fully free line of sight. The Radarcape demo station for this purpose is equipped with the 2 channel antenna diversity Radarcape. Such a Radarcape-2CH is equipped with two independant antenna inputs, one connected to an omni directional A3-ADSB antenna. The second input is connected to a home made 2.5m long yagi antenna.

Because there are no such long yagis for ADS-B on the market our Jetvision member Guenter has constructed this experiemental light weight (1kg), 2.5m long yagi 1090 MHz antenna with 27 elements. Its gain is 16.5dB (18.7dBi). This, within our experience, will truely be reached. In order not to be obstructed by other metallic elements on the mast the yagi is mounted on a bracket. Due to the light weight design mounting was even possible during a local storm.

The result of this is a drastic improve of the track of ground based vehicles at the airport, for example snow plowing trucks during winter time. The antenna also extends the range of the Radarcape demo towards east, where regularily 450 km distant aircraft can be observed. There is still some room for improvement, vehicles that are hidden between the buildings may be trackable with some more gain and picking up reflections. For that purpose an even longer yagi, with some 5-6m length, is in our thought.

If there is interest, we are willing to create these yagis as commerical products for customers, too. Please let us know on our support line (support@jetvision.de)

Ground traffic on Munich airport while cleaning the runway at January 17th, 2018

EDDM Ground View ADS-B with Yagi 1090 MHz

















Antennas at Jetvision headquarters:
Center: 2.5m long Yagi antenna, Very left: A3-ADSB for Radarcape demo, Very right: Active Diapason for Flightradar24 and for FLARM (dl4mea), unused experimental antenna.

Yogi 1090 MHz high gain

Gesamten Beitrag lesen
Veröffentlicht am von

What actually is Mode-A/C, Mode-S and ADS-B? A brief overview.

Gesamten Beitrag lesen: What actually is Mode-A/C, Mode-S and ADS-B? A brief overview.

Radar isn't a very old technology. Developed during WW2, it is 70 years old. Early radar was just to detect objects in the air. This was done by transmitting a powerful signal and waiting for the reflection from the flying object. The time between transmission and reception was twice the distance of the object. The position of the antenna provided the angular position. Something we still display even on modern systems. Such traditional systems are called primary radar.


However, due to geometry the altitude resolution on primary radar was not provided (or very inaccurate in systems with several beams). Also, if two aircraft were flying nearby, there was no identification provided for those bright spots on the screen. Due this demand a system was introduced permitting the aircraft to modify the received pulse: Using 12 bits, it returns either altitude or the squawk identification. The radar station has two request patterns which it transmits towards the aircraft, and the aircraft responds with either a Mode-A pattern for squawk or a Mode-C pattern for altitude. The pattern itself does not contain any information about its kind, so only the one who has requested that info will know how to post process. As a passive receiver such as we are, it is that we only hear a  number between zero and 4095, but we don't know the question.


With growing air traffic, air traffic controllers required more information about the aircraft. Also, they wanted to get control over the transmissions in a crowded airspace. This is when Mode-S became introduced. Not at least the "S" stands for "Selective". Mode-S transmissions contains some more information like higher resolution altitude, aircraft capabilities and identification. As a passive listener we now got the capability to distinguish between several formats and collect information about each single aircraft.


Last, one special frame format within the Mode-S protocol, so called DF-17, became introduced to indicate the position of the aircraft and some more information. In fact ADS-B is only one message within Mode-S. It requires 2 DF-17 frames to calculate the position unambiguous, the so called even and odd formats. 

Localisation using Mode-A/C, Mode-S and ADS-B:

Our Radarcape and the Mode-S Beast can receive Mode-AC messages and output them on the binary ports. But these messsages do not have position information within. They cannot be used for localisation within the processing capabilities of a Radarcape.

Also Mode-S does not contain location information, but as they have enougth information to distinguish among each other and combining data of at least 3 Radarcape with a precision time stamp and a process called Multilateration (MLAT) we are able to estimate the position of the aircraft from Mode-S transmissions.
Finally, using ADS-B transmissions, the aircraft directly tells us where it believes to be or where it wants us to think it currenly is.

Gesamten Beitrag lesen
Mehr über: ADS-B, Beast, Mode-A/C, Mode-S, Radarcape
Veröffentlicht am von

Munich Airport Running Event 2017

Gesamten Beitrag lesen: Munich Airport Running Event 2017

Members of the Jetvision team have successfully joined the 25th anniversary of the Munich airport running event. Participating on 5km, Florian (former shipping agent) managed a 4th place, while Elfriede (packaging and customs) and Günter (CEO) took the challenge of the 21km half marathon distance. The beautiful track went from the airport to the river Isar, along its meadows down to Freising and back to the airport on the other side of the river. First half was unusually hot and extremly humid, surely not ideal for running. Elfriede, with a time of 2:06:50 achieved 1st place in her age class and has won a nice trophy. Günter, still suffering from remains of a flu, anyway managed 2:11:32 hours. We say thanks to EDDM/MUC airport team for this great race and hospitality.


Gesamten Beitrag lesen
Veröffentlicht am von

Explaining Noise Figure and Gain

Gesamten Beitrag lesen: Explaining Noise Figure and Gain

We do see various offers for any kind of preamplifiers that are promising wonders, so let me give an explanation for the true important factors when using such devices. During my active time at ham radio I was very active in earth-moon-earth communication, that is sending signals to the moon and getting the echo back, up to 5.6 GHz, far beyond the ADS-B frequency of 1090 MHz. This is one of the most sophisticated operational modes in amateur radio, and needs high transmission power as well as most sensitive receivers. This knowledge was brougth into the receiver design of the Mode-S Beast as well as the Radarcape.

Now we do see a lot of preamps on the market. Most of the time gain is given for them, but the more important value of noise figure is missing. There are synonyms for both that can be understood easier:

  • Gain is like brightness of a monitor
  • Noise figure is contrast or somehow the minimum black level

You may quickly understand by these synonyms, once you have destroyed the black level of your picture into a kind of grey, you no longer never can see the small nuances of weak black symbols on your screen. It is the same with radio signals: Once you have destroyed the noise figure, you never will get it back. Even turning the brightness on (= adding gain), you never will recover the true cold black on your screen but instead simply amplify your grey even more.

This brings me to the cable: A cable is attenuation. With our video screen, this is similar to a milky glass in front of it. So you don't see the nice pure black any more but a little bit of grey. Of course, your bright symbols still appear readable. If now you insert an amplifier, the bright symbols will become brighter, but also the grey becomes brighter. But the weak nuances of black are lost.
However, if you amplify before passing the lossy section, you will amplify the nuances of black we're talking about, and they may be still readable behind the attenuation.

Even worse, electronic devices may become overloaded by the shiny bright parts. So this means with an amplifier after the cable and in front of the receiver, you may make things even worse. Only if your device is really deaf or has a lot of internal losses, an amplifier in direct front of the antenna input will improve the situation.

Our Active Diapason antennas for 868MHz (FLARM) and 1090 MHz (ADS-B) are equipped with an amplifier directly connected to the antenna element, which is the pure optimum. Their noise figure is somewhat 1 dB, a quite reasonable value for an antenna that partly sees warm earth within its diagram (less than, say 0.8 dB, only makes sense for space pointing antennas). They are sold with 20 m cable because the gain should not overdrive the receiver, and because this cable attenuation is completly knocked out due to the low noise figure.

Gesamten Beitrag lesen
Veröffentlicht am von

What is ADS-B, Which Requirements?

Gesamten Beitrag lesen: What is ADS-B, Which Requirements?

What do you really need for real time flight tracking?


We would like to give you an explanation about ADS-B in general, a brief overview, what kind of systems are there on the market and what are the differences between them. We are talking about system requirements and problems that could happen. Finally we get some aspects to Multilateration (MLAT), a very powerful method as well to track airplanes without ADS-B broadcast.

Check out our information and start to design your own flight tracking system!







  1. What is ADS-B?

  2. What do you need for real time flight tracking?

  3. ADS-B receiver types

  4. ADS-B public networks

  5. MLAT aircraft positioning

1. What is ADS-B?

Automatic Dependent Surveillance-Broadcast (ADS-B) is a worldwide aviation system on 1090 MHz used by aircraft in order to constantly broadcast their current position, altitude, air speed, identification, whether the aircraft is turning, climbing or descending, category of aircraft over a radio message. This functionality is the basic level of ADS-B and known as "ADS-B out”.

The current ADS-B system relies on data from the Global Positioning System (GPS), or any other navigation system e.g. GLONASS, INS. The maximum range of the system is line-of-sight, this means typically 200 nautical miles (370 km), because of the Earth curvature.

The ADS-B radio messages are received by air traffic control stations, and all other ADS-B equipped aircraft within reception range. Reception by aircraft of ADS-B data is known as "ADS-B in". The initial use of ADS-B was for air traffic control, for surveillance purposes and for enhancing pilot situational awareness. ADS-B is lower cost than conventional radar and permits higher quality surveillance of airborne and surface movements. ADS-B functionality also enhances surveillance on the airport surface, so it can also be used to monitor traffic on the taxiways and runways of an airport.


ADS-B is now widely used in air traffic, but not all aircraft are equipped with it. This is especially true for small private and military aircraft. However, other techniques such as MLAT (Multilateration) are used to capture these aircraft in the airspace as well.



2. What Do You Need for Real Time Flight Tracking?

The set up of your own ADS-B System can be from very easy to very complicated. This depends on some conditions at your location. In general, you need three things:

  • A 1090 MHz antenna
  • An ADS-B receiver
  • Software for displaying the results

1090 Mhz Antenna

There are some points to keep in mind. With very small antennas, sometimes even indoor, you can’t expect good results. The 1090 MHz antenna and its position is a key for your reception performance! Remember that an outdoor antenna must have a good grounding in order to discharge static electricity and for lightning protection. Another point is the length of your antenna cable. On such high frequencies cable losses will easily ruin even a good performing antenna. Thin and lossy cables longer than 15 m need an additional amplifier or active antenna to compensate the attenuation. If you keep all this in mind, you will have good conditions on the antenna side.

ADS-B Receiver

There are many ADS-B receivers on the market. Most of them are for use in airplanes and through required certifications they are very expensive. But there are some companies which have their business in real time flight tracking, with some very interesting receivers for commercial and private use. The most important types of receivers are described below.



All ADS-B receivers have no built-in user interface, except for a single receiver. For this, you always have to install your own software on your computer, for example, to process your raw data from your receiver and bring the flight positions and tracks to your screen. Commonly used software for flight tracking is e.g. PlanePlotter or RTL1090. Commercial companies have their own software, especially for ATC cards or special requirements of their customers.



If you have powerful transmitters, e.g. GSM or radar close to your ADS-B antenna, your receiver may be overloaded. This is, because these transmitters are very close with their frequencies to your required 1090 MHz signal. The solution is a bandpass filter. But be aware, most of the (cheap) filters have very bad parameters. They do not have a sufficient small bandwidth and quite often they have also significant attenuation. The result is, you will lose a lot of your signal strength. Together with a long cable distance, this is a very bad scenario. A filter must have a high, so called filter quality, this means a very low attenuation together with a small bandwidth. Physically those filters are bigger than others, and a little bit more expensive. But the result is very much better!

3. ADS-B Receiver Types

  • Raspberry Pi solution
  • Pure ADS-B receivers
  • All-in-one ADS-B receivers

The described ADS-B signals of the aircraft are free to be received, to increase aircraft security they are broadcast signals that should be received by others. The technical outlay for this is low. In addition to a 1090 MHz antenna suitable for the frequency range, an ADS-B receiver is required. There is a big difference between the receivers. Starting with a simple SDR USB dongle solution to a professional ADS-B receiver, there is a wide range. Especially in the lower price segment buzzes a lot of sellers. At this point we would like to present the different possibilities, advantages and disadvantages of the various concepts.

SDR USB Dongle (as ADS-B Receiver)
ADS-B USB dongles are SDR receivers (Software Defined Radio). This means that the dongle has only one adjustable receiving circuit but does not itself decode the ADS-B signals. Due to the broad frequency spectrum of these receivers, a bandpass filter must usually be connected in order not to exceed the receiver. The mostly used DVB-T dongles are made for television signals and do not have a very high dynamic range, so they lose performance in means of sensitivity on long range or situations when strong signals meet weak signals. 

To decode ADS-B signals, software logic is required on the computer. This can be done with an extra software, which also usually takes over the representation of the flight movements on maps or special air traffic maps.


Raspberry Pi Solution

In order to have computing power out of your PC, or to save power in a 24/7 operation, quite often small microcomputers such as the Raspberry Pi are used for ADS-B decoding. The receiver front end is represented by an ADS-B USB dongle. These combinations have a higher expenditure on installation components and software modules and are only for freaks and hobbyists. There are, however, providers who offer complete solutions. The reception power is determined as described above by the ADS-B USB dongle.


Pure ADS-B Receivers

Pure ADS-B receivers have a receiving circuit precisely adapted to this application and the corresponding decoding logic. Via interfaces (network, USB or serial) the data can be processed for display via an external software. The advantage of a pure ADS-B receiver is the high sensitivity, separation sharpness and overload resistance. This ends in better reception results (long distance), especially under difficult conditions.

This technology means that pure ADS-B receivers are more expensive than dongle solutions. Receivers built for aircraft installations even are high price segmented, because for these equipment expensive test approvals are necessary.

For the ambitious hobbyist, however there are also high-quality ADS-B receivers as prefabricated kits available. The performance is at the level of finished receivers, of course these kits are cheaper, because they are made for handicraft enthusiasts with experience in soldering and assembling of electronic components.


All-In-One ADS Receivers

These receivers offer a particular advantage. All components required for operation and user interface (flight tracking maps and more) are already installed in the receiver itself. Access is via the network with a web browser. No extra software on the PC, no cumbersome connection, minimal installation effort. Despite the simplicity, professional requirements such as MLAT, RAW data access via various interfaces and ports, are supported. As well as the possibility to send data to known networks through built-in feeders. Worldwide there is only one receiver on the market having all-in-one features. It's called Radarcape.

4. ADS-B Networks

The most common form of flight tracking networks are the networks of Flightradar24, FlightAware, Opensky Network, Planefinder and some others. Some content and functions are freely available, others must be booked for a fee.

There are also smaller networks with other features than public flight tracking. Here, the provider runs a server that supports various models such as closed user groups, offers multilateration to localize aircraft which broadcasting only Mode-S signals without positions etc., remote access via a mobile app, fleet watch etc. 


5. MLAT Aircraft Positioning

Many aircraft don’t broadcast ADS-B messages. This class of aircraft we find in types like Cessnas or military jets. But most of them have a Mode-S transponder. But this broadcast messages don’t have any information about position, altitude etc. With a special mathematical algorithm, called TDOA (Time Delay of Arrival), it is possible to calculate the aircraft position based on data of a minimum of three receivers. With this solution a central server is required for the mathematical calculations. Each receiver send its data to the server. Based on three data streams the position, altitude etc. of such an aircraft is calculated and the result is send to all connected receivers. This central server is called MLAT-Server, and is the base of all MLAT capabilities in an flight tracking network supporting Multilateration. To get a brief overview see also our post about MLAT.

Gesamten Beitrag lesen
Veröffentlicht am von

Multilateration (MLAT) Overview

Gesamten Beitrag lesen: Multilateration (MLAT) Overview


Airplanes, that only have a 1090 MHz Mode-S transponder, without an ADS-B function do not send data about their position. Without extra effort these aircrafts are not visible for display in an ADS-B system or flight tracking network.For this, the continuous and automatically transmitted status messages of the Mode-S transponder of an aircraft can be used for mathematical calculations, the so-called multilateration method (MLAT) for position determination.


How It Works

The position of these aircraft (without ADS-B) can be detected by the use of at least 3 receivers for a common reception area. For this purpose, the receivers transmit all received Mode-S telegrams via Internet/LAN to a central MLAT server, which very precisely calculates the position data from the transit times of the receive signals (TDOA method). The position data can be returned to each receiver via the data channel.


The positional accuracy depends on the number of receivers for the receiving area. The more data from different recipients is available, the more accurate the result. The update performance on the receivers is approximately one second. Our server typically calculates 1-5 locations per aircraft and second, of which one per second will be sent back to the receivers. The latency is arround 1.5 seconds.


The significant advantage of our Radarcape ADS-B receivers is a nanosecond accuracy of the timestamps due to GPS synchronisation. Due to this MLAT calculations within the Radarcape system do not need beacon transmitters or reference ADS-B aircraft for correct operation. In difference to other receivers in the price class, our receivers are equipped with a high precision GPS synchronized clock and the timestamps have an accuracy of app. 50nS. As a result, each individual calculation already has excellent accuracy, and can be used without averaging. Furthermore, it is also possible to make MLAT calculations for ADS-B aircraft if their data are doubtful or should be checked. The bandwidth requirement of the required data network is only a few kilobytes/sec upstream and is also scalable.



Advantages of a Radarcape MLAT Network

  • Display of aircraft positions determined by MLAT and ADS-B
  • Mode-S, ADS-B Messages can be evaluated for MLAT
  • High accuracy of the position data already from 3 receivers
  • Low bandwidth requirements of the network (GSM transmission possible)
  • High update speed on the receivers through optimized processes
  • Non public and local MLAT systems with filters, locks, etc. possible

Applications for a MLAT Network

  • Air traffic observation for a defined monitoring area
  • Airfield flight movements
  • Monitoring ground movements on an airfield
  • Bypass of ADS-B spoofing
  • Independence from ADS-B and for verification purposes

  • Airfield noise measurements

Gesamten Beitrag lesen
Veröffentlicht am von

How do I find my Radarcape

Gesamten Beitrag lesen: How do I find my Radarcape

Do you have one of the following problems?

How do I access my Radarcape in my local network?

My Radarcapes’ IP-Address changed and I do not know the new address.

How do I get an overview of all my local Radarcapes?

I don't want to use the roundabout way over my router everytime the IP changes.


One easy solution: CapeFinder

We created a small tool to offer you a quick and easy way to get information of all Radarcapes in your local network. CapeFinder works out of the box, you just need to download and start it.


What does it do and how does it work?

CapeFinder automatically detects all network interfaces. Then it starts scanning to find connected Radarcapes. In addition, it gathers some information like the current IP-Address, Hostname, Software-Version and the MAC-Address.


Where to get and how to use?

Simple as that: download the latest version, open it on your PC and allow network access if asked.
Use our wiki page to download the latest version:http://wiki.modesbeast.com/Radarcape:CapeFinder

Gesamten Beitrag lesen
Veröffentlicht am von

The Development of Our Flight Tracking Products

Gesamten Beitrag lesen: The Development of Our Flight Tracking Products

Ham radio experience

My motivation of this project comes from a more than 25 years ham radio experience, mainly weak signal and GHz operation, a lot of interest in signal processing, and a professional background as an electronic development engineer.

I managed to combine all my knowledge in this project, and was able to fill some gaps with the special knowledge of some friends with special know-how in microwave and digital electronics.

It all began around 1995 when I mainly participated in radio contests on 144 MHz up to 2320 MHz with always good success. However, on the upper bands there was always one that was better. I heard that part of his success was his efficiency in aircraft scatter, a method when on 1296 MHz and 2320 MHz an aircraft is used as passive reflector. I also used this mode, mainly to the Netherlands, but wasted a lot of time waiting for aircraft passing the hot spot. A flight tracker called SBS-1 was the key for my competitor, which showed that there are aircraft in the scatter zone. However, for that time, this unit was far out of reach within my budget. Also, the thought of a closed system never attracted me very much.

ADS-B Receiver

Around 2007 I found more about ADS-B Receiver, 1090 MHz antennas and Software like Planeplotter, the miniADSB receiver and the PIC decoder and brought it into work. Back to ham radio thinking, I was surprised about the bad performance and started tweaking. The first result was the floating comparator, which adjusted the digitial comparator automatically to the signal level, thus avoiding the awful donut effect of this set-up. Driven by an "is that all?" thinking, I asked how reception could be done without the bottlenecks of a PIC, using an FPGA as decoder. Not knowing anything about FPGA, I started teaching myself. I avoided some weaks of the existing designs and brought in my experience from Earth-Moon-Earth communication. After some time, the ADS-B Mode-S Beast was born, which was even at the early stages outperforming all existing units.

By the way, why is it called Beast? Well, at that time Planeplotter only had some devices like SBS-1 and PIC decoders as frontend, and their weak performance resulted in only a few frames per second. With the Beast, Planeplotter suddenly had to handle much more messages and went into a stall. "Hey, what a little ugly beast", I thought, and so the name was born. Those early devices did have so less performance that even a hexdump "AVR format" or CSV protocol (Port 30003) was enough for data transmission, and I introduced the Beast-Binary protocol.


A few years later I sat together with some friends, talking about aircraft not yet localized and had the idea to catch them with multilateration (MLAT). At around the same time little Linux based boards grew on the market, mainly Raspberry Pi and Beaglebone. This matched to our need of remote operation and LAN interface, transporting the data to a central server - the Mode-S Beast only had USB and a not handsome and expensive LAN solution based on Xport. I decided to use the Beaglebone because it has connectors that allow an easy integration into a metal case and because of power supply problems of the Raspberry Pi. For easy and accurate multilateration I choose a GPS module as timestamp. The add-on boards on the Beaglebone are named "capes", and so my ADS-B flight decoder was named "Radarcape".

Flightradar24 asked for the Radarcape as backbone for their own network with their proprietary software in order to provide updates for their flight tracking app. They showed me an ADS-B antenna which was hardly worth the name. Due to my ham history, I found a manufacturer in Italy who makes very good antennas which really proof the given technical data. Our portfolio widened up and so the web shop warehouse increased to a whole set up.


In 2014 I joined the activities of existing jetvision, who had some solutions with RTL-SDR and USB DVB-T dongles, and my meanwhile founded company took over the brand "jetvision". In May 2016 my company took over the whole business of these and Planevision Systems offers rack solutions based on the Radarcape only. We now are a team of around 8 people working for the development, marketing and sales with a great support by friends and other companies in all themes.

(Günter, CEO)

Gesamten Beitrag lesen